Book Service Now

We have come across this great article on How to Install a Bathtub listed below on the web and thought it made perfect sense to write about it with you in this article.

Setting up a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard task. If the old bathtub is conveniently available, the job can move speedily; if you need to open up a wall surface to eliminate the old tub and place the brand-new tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have certified yourself for the job and also fit attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list must comprise the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Planning for the Setup

Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the adaptable tap adapters to the bottom of the two taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final setting.

Removing Old Touches

If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be fairly problematic because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

Setting up the Tub

Utilizing both wood boards under its feet, position the bath tub in the required placement. The wood boards are handy in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the tub until the spirit level reads level.
To install taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly resolve it into its final placement.

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer provided backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

Tiling Around the Bath tub

In the area where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We were introduced to that article about How to Install a Bathtub from a friend on a different web page. Do you know anybody else who is in the market for the subject? Be sure promote it. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Schedule Today